![dell perc h200 disk passthrough temperature dell perc h200 disk passthrough temperature](https://www.serverschmiede.com/images/product_images/thumbnail/dell-perc-h330-12gb-s-sas-raid-controller-pcie-x8-for-hdd-ssd-raid-0151050-non-raid-hba-mode-pass-through-06h1g0-620-m-2.jpg)
- #Dell perc h200 disk passthrough temperature install
- #Dell perc h200 disk passthrough temperature 64 Bit
- #Dell perc h200 disk passthrough temperature driver
Possibly stupid question, but could the mpt3sas module from 5.13.6 be backported to 5.11.22? or, perhaps more achievable, could the module in 5.11.22 that is currently in use be rolled back to the state it was in 5.11.12?
![dell perc h200 disk passthrough temperature dell perc h200 disk passthrough temperature](https://i.redd.it/5tn5hurfc7ix.jpg)
That is rather early in the 5.13 dev cycle (pre-rc1) however, it was not applied to the 5.11.22 tree from what I can tell. Despite the commit message listed in the header, there's a fair bit to that rollup, some of which automatically backs down the queue depth as necessary.
![dell perc h200 disk passthrough temperature dell perc h200 disk passthrough temperature](https://i.ebayimg.com/images/g/QmEAAOSwGu9eurq4/s-l300.jpg)
Which has significant changes to the mpt3sas module. There does seem to be a large merge here: I've also been looking at commits to the mpt3sas module in the 5.13.y tree. So it appears something possibly specific to cards with IT firmware, or just this specific model of LSI card, but that derivative branded cards like the M1015, H200, H310, etc - are likely unaffected.Īt this point, it might be useful for someone with an H200 that was flashed with 9211 IT firmware to test this, and help narrow down where specifically the issue is that's causing the module to call for the diag_reset. I also tried the fix documented here for an issue that was present in 5.8, thinking there may have been a regression, as one of the dmesg lines I'm getting is similar, but there was no change:
#Dell perc h200 disk passthrough temperature install
I went back to test if my 9200-8e worked under the install media -1 kernel, and it does not work. My brother has a Dell r710 with a perc H200 (basically an LSI 9211-8i with some special-ish hybrid IR/IT firmware - his is not crossflashed), and using the install media for proxmox 7.0, his card initialized fine. I'm working to narrow down what the exact issue I'm experiencing is. Though if it is, it's rather odd that the controller would be fine under earlier kernels if it is hardware weirdness.Īs alluded to, if this is a bug, I believe it would have been introduced in 5.11.20 - possibly in either of these two commits, though I could definitely be wrong, but they are among the very few changes to the mpt3sas module between 5.11.12 and 5.11.22 Is this actually a bug, or is it something in my specific hardware that's not behaving? Is there anyone else out there experiencing this problem with any other LSI SAS2008 based HBAs under proxmox 7? The controller sees the drives just fine, if I go into the controller bios during boot, all drives and backplanes are listed in the topology listing. The proxmox kernel is up to date, 5.11.22-3 as of writing. My motherboard is on the latest available bios, and the 9200-8e is on the latest available firmware (P20). mptctl: /dev/mptctl (major,minor=10,220)Īnd obviously none of the disks attached to the controller show up after boot.
#Dell perc h200 disk passthrough temperature driver
mptctl: Registered with Fusion MPT base driver Fusion MPT misc device (ioctl) driver 3.04.20 mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:12013/_scsih_probe()! mpt2sas_cm0: Invalid host diagnostic register value
#Dell perc h200 disk passthrough temperature 64 Bit
mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (65787168 kB) mpt3sas 0000:41:00.0: can't disable ASPM OS doesn't have ASPM control